From 8b45597a9a24925b3a62c4fe793661bfbc682bcc Mon Sep 17 00:00:00 2001 From: Stef Walter Date: Sat, 28 Jan 2006 00:00:04 +0000 Subject: Add MIBS that we distribute with the app. --- mibs/EtherLike-MIB.txt | 1862 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1862 insertions(+) create mode 100644 mibs/EtherLike-MIB.txt (limited to 'mibs/EtherLike-MIB.txt') diff --git a/mibs/EtherLike-MIB.txt b/mibs/EtherLike-MIB.txt new file mode 100644 index 0000000..dcec7ce --- /dev/null +++ b/mibs/EtherLike-MIB.txt @@ -0,0 +1,1862 @@ +EtherLike-MIB DEFINITIONS ::= BEGIN + + IMPORTS + MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, + Integer32, Counter32, Counter64, mib-2, transmission + FROM SNMPv2-SMI + MODULE-COMPLIANCE, OBJECT-GROUP + FROM SNMPv2-CONF + TruthValue + FROM SNMPv2-TC + ifIndex, InterfaceIndex + FROM IF-MIB; + + etherMIB MODULE-IDENTITY + LAST-UPDATED "200309190000Z" -- September 19, 2003 + ORGANIZATION "IETF Ethernet Interfaces and Hub MIB + Working Group" + CONTACT-INFO + "WG E-mail: hubmib@ietf.org + To subscribe: hubmib-request@ietf.org + + Chair: Dan Romascanu + Postal: Avaya Inc. + Atidum Technology Park, Bldg. 3 + Tel Aviv 61131 + Israel + Tel: +972 3 645 8414 + E-mail: dromasca@avaya.com + + Editor: John Flick + Postal: Hewlett-Packard Company + 8000 Foothills Blvd. M/S 5557 + Roseville, CA 95747-5557 + USA + Tel: +1 916 785 4018 + Fax: +1 916 785 1199 + E-mail: johnf@rose.hp.com" + DESCRIPTION "The MIB module to describe generic objects for + ethernet-like network interfaces. + + The following reference is used throughout this + MIB module: + + [IEEE 802.3 Std] refers to: + IEEE Std 802.3, 2002 Edition: 'IEEE Standard + + for Information technology - + Telecommunications and information exchange + between systems - Local and metropolitan + area networks - Specific requirements - + Part 3: Carrier sense multiple access with + collision detection (CSMA/CD) access method + and physical layer specifications', as + amended by IEEE Std 802.3ae-2002: + 'Amendment: Media Access Control (MAC) + Parameters, Physical Layer, and Management + Parameters for 10 Gb/s Operation', August, + 2002. + + Of particular interest is Clause 30, '10 Mb/s, + 100 Mb/s, 1000 Mb/s, and 10 Gb/s Management'. + + Copyright (C) The Internet Society (2003). This + version of this MIB module is part of RFC 3635; + see the RFC itself for full legal notices." + + REVISION "200309190000Z" -- September 19, 2003 + DESCRIPTION "Updated to include support for 10 Gb/sec + interfaces. This resulted in the following + revisions: + + - Updated dot3StatsAlignmentErrors and + dot3StatsSymbolErrors DESCRIPTIONs to + reflect behaviour at 10 Gb/s + - Added dot3StatsRateControlAbility and + dot3RateControlStatus for management + of the Rate Control function in 10 Gb/s + WAN applications + - Added 64-bit versions of all counters + that are used on high-speed ethernet + interfaces + - Added object groups to contain the new + objects + - Deprecated etherStatsBaseGroup and + split into etherStatsBaseGroup2 and + etherStatsHalfDuplexGroup, so that + interfaces which can only operate at + full-duplex do not need to implement + half-duplex-only statistics + - Deprecated dot3Compliance and replaced + it with dot3Compliance2, which includes + the compliance information for the new + object groups + + In addition, the dot3Tests and dot3Errors + object identities have been deprecated, + since there is no longer a standard method + for using them. + + This version published as RFC 3635." + + REVISION "199908240400Z" -- August 24, 1999 + DESCRIPTION "Updated to include support for 1000 Mb/sec + interfaces and full-duplex interfaces. + This version published as RFC 2665." + + REVISION "199806032150Z" -- June 3, 1998 + DESCRIPTION "Updated to include support for 100 Mb/sec + interfaces. + This version published as RFC 2358." + + REVISION "199402030400Z" -- February 3, 1994 + DESCRIPTION "Initial version, published as RFC 1650." + ::= { mib-2 35 } + + etherMIBObjects OBJECT IDENTIFIER ::= { etherMIB 1 } + + dot3 OBJECT IDENTIFIER ::= { transmission 7 } + + -- the Ethernet-like Statistics group + + dot3StatsTable OBJECT-TYPE + SYNTAX SEQUENCE OF Dot3StatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "Statistics for a collection of ethernet-like + interfaces attached to a particular system. + There will be one row in this table for each + ethernet-like interface in the system." + ::= { dot3 2 } + + dot3StatsEntry OBJECT-TYPE + SYNTAX Dot3StatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "Statistics for a particular interface to an + ethernet-like medium." + INDEX { dot3StatsIndex } + ::= { dot3StatsTable 1 } + + Dot3StatsEntry ::= + SEQUENCE { + + dot3StatsIndex InterfaceIndex, + dot3StatsAlignmentErrors Counter32, + dot3StatsFCSErrors Counter32, + dot3StatsSingleCollisionFrames Counter32, + dot3StatsMultipleCollisionFrames Counter32, + dot3StatsSQETestErrors Counter32, + dot3StatsDeferredTransmissions Counter32, + dot3StatsLateCollisions Counter32, + dot3StatsExcessiveCollisions Counter32, + dot3StatsInternalMacTransmitErrors Counter32, + dot3StatsCarrierSenseErrors Counter32, + dot3StatsFrameTooLongs Counter32, + dot3StatsInternalMacReceiveErrors Counter32, + dot3StatsEtherChipSet OBJECT IDENTIFIER, + dot3StatsSymbolErrors Counter32, + dot3StatsDuplexStatus INTEGER, + dot3StatsRateControlAbility TruthValue, + dot3StatsRateControlStatus INTEGER + } + + dot3StatsIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only -- read-only since originally an + -- SMIv1 index + STATUS current + DESCRIPTION "An index value that uniquely identifies an + interface to an ethernet-like medium. The + interface identified by a particular value of + this index is the same interface as identified + by the same value of ifIndex." + REFERENCE "RFC 2863, ifIndex" + ::= { dot3StatsEntry 1 } + + dot3StatsAlignmentErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames received on a particular + interface that are not an integral number of + octets in length and do not pass the FCS check. + + The count represented by an instance of this + object is incremented when the alignmentError + status is returned by the MAC service to the + LLC (or other MAC user). Received frames for + which multiple error conditions pertain are, + according to the conventions of IEEE 802.3 + Layer Management, counted exclusively according + + to the error status presented to the LLC. + + This counter does not increment for group + encoding schemes greater than 4 bits per group. + + For interfaces operating at 10 Gb/s, this + counter can roll over in less than 5 minutes if + it is incrementing at its maximum rate. Since + that amount of time could be less than a + management station's poll cycle time, in order + to avoid a loss of information, a management + station is advised to poll the + dot3HCStatsAlignmentErrors object for 10 Gb/s + or faster interfaces. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.7, + aAlignmentErrors" + ::= { dot3StatsEntry 2 } + + dot3StatsFCSErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames received on a particular + interface that are an integral number of octets + in length but do not pass the FCS check. This + count does not include frames received with + frame-too-long or frame-too-short error. + + The count represented by an instance of this + object is incremented when the frameCheckError + status is returned by the MAC service to the + LLC (or other MAC user). Received frames for + which multiple error conditions pertain are, + according to the conventions of IEEE 802.3 + Layer Management, counted exclusively according + to the error status presented to the LLC. + + Note: Coding errors detected by the physical + layer for speeds above 10 Mb/s will cause the + frame to fail the FCS check. + + For interfaces operating at 10 Gb/s, this + counter can roll over in less than 5 minutes if + + it is incrementing at its maximum rate. Since + that amount of time could be less than a + management station's poll cycle time, in order + to avoid a loss of information, a management + station is advised to poll the + dot3HCStatsFCSErrors object for 10 Gb/s or + faster interfaces. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.6, + aFrameCheckSequenceErrors." + ::= { dot3StatsEntry 3 } + + dot3StatsSingleCollisionFrames OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames that are involved in a single + collision, and are subsequently transmitted + successfully. + + A frame that is counted by an instance of this + object is also counted by the corresponding + instance of either the ifOutUcastPkts, + ifOutMulticastPkts, or ifOutBroadcastPkts, + and is not counted by the corresponding + instance of the dot3StatsMultipleCollisionFrames + object. + + This counter does not increment when the + interface is operating in full-duplex mode. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.3, + aSingleCollisionFrames." + ::= { dot3StatsEntry 4 } + + dot3StatsMultipleCollisionFrames OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames that are involved in more + + than one collision and are subsequently + transmitted successfully. + + A frame that is counted by an instance of this + object is also counted by the corresponding + instance of either the ifOutUcastPkts, + ifOutMulticastPkts, or ifOutBroadcastPkts, + and is not counted by the corresponding + instance of the dot3StatsSingleCollisionFrames + object. + + This counter does not increment when the + interface is operating in full-duplex mode. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.4, + aMultipleCollisionFrames." + ::= { dot3StatsEntry 5 } + + dot3StatsSQETestErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of times that the SQE TEST ERROR + is received on a particular interface. The + SQE TEST ERROR is set in accordance with the + rules for verification of the SQE detection + mechanism in the PLS Carrier Sense Function as + described in IEEE Std. 802.3, 2000 Edition, + section 7.2.4.6. + + This counter does not increment on interfaces + operating at speeds greater than 10 Mb/s, or on + interfaces operating in full-duplex mode. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 7.2.4.6, also 30.3.2.1.4, + aSQETestErrors." + ::= { dot3StatsEntry 6 } + + dot3StatsDeferredTransmissions OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames for which the first + transmission attempt on a particular interface + is delayed because the medium is busy. + + The count represented by an instance of this + object does not include frames involved in + collisions. + + This counter does not increment when the + interface is operating in full-duplex mode. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.9, + aFramesWithDeferredXmissions." + ::= { dot3StatsEntry 7 } + + dot3StatsLateCollisions OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "The number of times that a collision is + detected on a particular interface later than + one slotTime into the transmission of a packet. + + A (late) collision included in a count + represented by an instance of this object is + also considered as a (generic) collision for + purposes of other collision-related + statistics. + + This counter does not increment when the + interface is operating in full-duplex mode. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.10, + aLateCollisions." + ::= { dot3StatsEntry 8 } + + dot3StatsExcessiveCollisions OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames for which transmission on a + particular interface fails due to excessive + collisions. + + This counter does not increment when the + interface is operating in full-duplex mode. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.11, + aFramesAbortedDueToXSColls." + ::= { dot3StatsEntry 9 } + + dot3StatsInternalMacTransmitErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames for which transmission on a + particular interface fails due to an internal + MAC sublayer transmit error. A frame is only + counted by an instance of this object if it is + not counted by the corresponding instance of + either the dot3StatsLateCollisions object, the + dot3StatsExcessiveCollisions object, or the + dot3StatsCarrierSenseErrors object. + + The precise meaning of the count represented by + an instance of this object is implementation- + specific. In particular, an instance of this + object may represent a count of transmission + errors on a particular interface that are not + otherwise counted. + + For interfaces operating at 10 Gb/s, this + counter can roll over in less than 5 minutes if + it is incrementing at its maximum rate. Since + that amount of time could be less than a + management station's poll cycle time, in order + to avoid a loss of information, a management + station is advised to poll the + dot3HCStatsInternalMacTransmitErrors object for + 10 Gb/s or faster interfaces. + + Discontinuities in the value of this counter can + + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.12, + aFramesLostDueToIntMACXmitError." + ::= { dot3StatsEntry 10 } + + dot3StatsCarrierSenseErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "The number of times that the carrier sense + condition was lost or never asserted when + attempting to transmit a frame on a particular + interface. + + The count represented by an instance of this + object is incremented at most once per + transmission attempt, even if the carrier sense + condition fluctuates during a transmission + attempt. + + This counter does not increment when the + interface is operating in full-duplex mode. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.13, + aCarrierSenseErrors." + ::= { dot3StatsEntry 11 } + + -- { dot3StatsEntry 12 } is not assigned + + dot3StatsFrameTooLongs OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames received on a particular + interface that exceed the maximum permitted + frame size. + + The count represented by an instance of this + object is incremented when the frameTooLong + status is returned by the MAC service to the + LLC (or other MAC user). Received frames for + which multiple error conditions pertain are, + according to the conventions of IEEE 802.3 + Layer Management, counted exclusively according + to the error status presented to the LLC. + + For interfaces operating at 10 Gb/s, this + counter can roll over in less than 80 minutes if + it is incrementing at its maximum rate. Since + that amount of time could be less than a + management station's poll cycle time, in order + to avoid a loss of information, a management + station is advised to poll the + dot3HCStatsFrameTooLongs object for 10 Gb/s + or faster interfaces. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.25, + aFrameTooLongErrors." + ::= { dot3StatsEntry 13 } + + -- { dot3StatsEntry 14 } is not assigned + + -- { dot3StatsEntry 15 } is not assigned + + dot3StatsInternalMacReceiveErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames for which reception on a + particular interface fails due to an internal + MAC sublayer receive error. A frame is only + counted by an instance of this object if it is + not counted by the corresponding instance of + either the dot3StatsFrameTooLongs object, the + dot3StatsAlignmentErrors object, or the + dot3StatsFCSErrors object. + + The precise meaning of the count represented by + an instance of this object is implementation- + specific. In particular, an instance of this + object may represent a count of receive errors + on a particular interface that are not + otherwise counted. + + For interfaces operating at 10 Gb/s, this + counter can roll over in less than 5 minutes if + + it is incrementing at its maximum rate. Since + that amount of time could be less than a + management station's poll cycle time, in order + to avoid a loss of information, a management + station is advised to poll the + dot3HCStatsInternalMacReceiveErrors object for + 10 Gb/s or faster interfaces. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.15, + aFramesLostDueToIntMACRcvError." + ::= { dot3StatsEntry 16 } + + dot3StatsEtherChipSet OBJECT-TYPE + SYNTAX OBJECT IDENTIFIER + MAX-ACCESS read-only + STATUS deprecated + DESCRIPTION "******** THIS OBJECT IS DEPRECATED ******** + + This object contains an OBJECT IDENTIFIER + which identifies the chipset used to + realize the interface. Ethernet-like + interfaces are typically built out of + several different chips. The MIB implementor + is presented with a decision of which chip + to identify via this object. The implementor + should identify the chip which is usually + called the Medium Access Control chip. + If no such chip is easily identifiable, + the implementor should identify the chip + which actually gathers the transmit + and receive statistics and error + indications. This would allow a + manager station to correlate the + statistics and the chip generating + them, giving it the ability to take + into account any known anomalies + in the chip. + + This object has been deprecated. Implementation + feedback indicates that it is of limited use for + debugging network problems in the field, and + the administrative overhead involved in + maintaining a registry of chipset OIDs is not + justified." + ::= { dot3StatsEntry 17 } + + dot3StatsSymbolErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "For an interface operating at 100 Mb/s, the + number of times there was an invalid data symbol + when a valid carrier was present. + + For an interface operating in half-duplex mode + at 1000 Mb/s, the number of times the receiving + media is non-idle (a carrier event) for a period + of time equal to or greater than slotTime, and + during which there was at least one occurrence + of an event that causes the PHY to indicate + 'Data reception error' or 'carrier extend error' + on the GMII. + + For an interface operating in full-duplex mode + at 1000 Mb/s, the number of times the receiving + media is non-idle (a carrier event) for a period + of time equal to or greater than minFrameSize, + and during which there was at least one + occurrence of an event that causes the PHY to + indicate 'Data reception error' on the GMII. + + For an interface operating at 10 Gb/s, the + number of times the receiving media is non-idle + (a carrier event) for a period of time equal to + or greater than minFrameSize, and during which + there was at least one occurrence of an event + that causes the PHY to indicate 'Receive Error' + on the XGMII. + + The count represented by an instance of this + object is incremented at most once per carrier + event, even if multiple symbol errors occur + during the carrier event. This count does + not increment if a collision is present. + + This counter does not increment when the + interface is operating at 10 Mb/s. + + For interfaces operating at 10 Gb/s, this + counter can roll over in less than 5 minutes if + it is incrementing at its maximum rate. Since + that amount of time could be less than a + + management station's poll cycle time, in order + to avoid a loss of information, a management + station is advised to poll the + dot3HCStatsSymbolErrors object for 10 Gb/s + or faster interfaces. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.2.1.5, + aSymbolErrorDuringCarrier." + ::= { dot3StatsEntry 18 } + + dot3StatsDuplexStatus OBJECT-TYPE + SYNTAX INTEGER { + unknown(1), + halfDuplex(2), + fullDuplex(3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION "The current mode of operation of the MAC + entity. 'unknown' indicates that the current + duplex mode could not be determined. + + Management control of the duplex mode is + accomplished through the MAU MIB. When + an interface does not support autonegotiation, + or when autonegotiation is not enabled, the + duplex mode is controlled using + ifMauDefaultType. When autonegotiation is + supported and enabled, duplex mode is controlled + using ifMauAutoNegAdvertisedBits. In either + case, the currently operating duplex mode is + reflected both in this object and in ifMauType. + + Note that this object provides redundant + information with ifMauType. Normally, redundant + objects are discouraged. However, in this + instance, it allows a management application to + determine the duplex status of an interface + without having to know every possible value of + ifMauType. This was felt to be sufficiently + valuable to justify the redundancy." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.32, + aDuplexStatus." + ::= { dot3StatsEntry 19 } + + dot3StatsRateControlAbility OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION "'true' for interfaces operating at speeds above + 1000 Mb/s that support Rate Control through + lowering the average data rate of the MAC + sublayer, with frame granularity, and 'false' + otherwise." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.33, + aRateControlAbility." + ::= { dot3StatsEntry 20 } + + dot3StatsRateControlStatus OBJECT-TYPE + SYNTAX INTEGER { + rateControlOff(1), + rateControlOn(2), + unknown(3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION "The current Rate Control mode of operation of + the MAC sublayer of this interface." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.34, + aRateControlStatus." + ::= { dot3StatsEntry 21 } + + -- the Ethernet-like Collision Statistics group + + -- Implementation of this group is optional; it is appropriate + -- for all systems which have the necessary metering + + dot3CollTable OBJECT-TYPE + SYNTAX SEQUENCE OF Dot3CollEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "A collection of collision histograms for a + particular set of interfaces." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.30, + aCollisionFrames." + ::= { dot3 5 } + + dot3CollEntry OBJECT-TYPE + SYNTAX Dot3CollEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "A cell in the histogram of per-frame + collisions for a particular interface. An + + instance of this object represents the + frequency of individual MAC frames for which + the transmission (successful or otherwise) on a + particular interface is accompanied by a + particular number of media collisions." + INDEX { ifIndex, dot3CollCount } + ::= { dot3CollTable 1 } + + Dot3CollEntry ::= + SEQUENCE { + dot3CollCount Integer32, + dot3CollFrequencies Counter32 + } + + -- { dot3CollEntry 1 } is no longer in use + + dot3CollCount OBJECT-TYPE + SYNTAX Integer32 (1..16) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "The number of per-frame media collisions for + which a particular collision histogram cell + represents the frequency on a particular + interface." + ::= { dot3CollEntry 2 } + + dot3CollFrequencies OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of individual MAC frames for which the + transmission (successful or otherwise) on a + particular interface occurs after the + frame has experienced exactly the number + of collisions in the associated + dot3CollCount object. + + For example, a frame which is transmitted + on interface 77 after experiencing + exactly 4 collisions would be indicated + by incrementing only dot3CollFrequencies.77.4. + No other instance of dot3CollFrequencies would + be incremented in this example. + + This counter does not increment when the + interface is operating in full-duplex mode. + + Discontinuities in the value of this counter can + + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + ::= { dot3CollEntry 3 } + + dot3ControlTable OBJECT-TYPE + SYNTAX SEQUENCE OF Dot3ControlEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "A table of descriptive and status information + about the MAC Control sublayer on the + ethernet-like interfaces attached to a + particular system. There will be one row in + this table for each ethernet-like interface in + the system which implements the MAC Control + sublayer. If some, but not all, of the + ethernet-like interfaces in the system implement + the MAC Control sublayer, there will be fewer + rows in this table than in the dot3StatsTable." + ::= { dot3 9 } + + dot3ControlEntry OBJECT-TYPE + SYNTAX Dot3ControlEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "An entry in the table, containing information + about the MAC Control sublayer on a single + ethernet-like interface." + INDEX { dot3StatsIndex } + ::= { dot3ControlTable 1 } + + Dot3ControlEntry ::= + SEQUENCE { + dot3ControlFunctionsSupported BITS, + dot3ControlInUnknownOpcodes Counter32, + dot3HCControlInUnknownOpcodes Counter64 + } + + dot3ControlFunctionsSupported OBJECT-TYPE + SYNTAX BITS { + pause(0) -- 802.3 flow control + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A list of the possible MAC Control functions + implemented for this interface." + REFERENCE "[IEEE 802.3 Std.], 30.3.3.2, + aMACControlFunctionsSupported." + ::= { dot3ControlEntry 1 } + + dot3ControlInUnknownOpcodes OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of MAC Control frames received on this + interface that contain an opcode that is not + supported by this device. + + For interfaces operating at 10 Gb/s, this + counter can roll over in less than 5 minutes if + it is incrementing at its maximum rate. Since + that amount of time could be less than a + management station's poll cycle time, in order + to avoid a loss of information, a management + station is advised to poll the + dot3HCControlInUnknownOpcodes object for 10 Gb/s + or faster interfaces. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.3.5, + aUnsupportedOpcodesReceived" + ::= { dot3ControlEntry 2 } + + dot3HCControlInUnknownOpcodes OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of MAC Control frames received on this + interface that contain an opcode that is not + supported by this device. + + This counter is a 64 bit version of + dot3ControlInUnknownOpcodes. It should be used + on interfaces operating at 10 Gb/s or faster. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.3.5, + aUnsupportedOpcodesReceived" + ::= { dot3ControlEntry 3 } + + dot3PauseTable OBJECT-TYPE + SYNTAX SEQUENCE OF Dot3PauseEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "A table of descriptive and status information + about the MAC Control PAUSE function on the + ethernet-like interfaces attached to a + particular system. There will be one row in + this table for each ethernet-like interface in + the system which supports the MAC Control PAUSE + function (i.e., the 'pause' bit in the + corresponding instance of + dot3ControlFunctionsSupported is set). If some, + but not all, of the ethernet-like interfaces in + the system implement the MAC Control PAUSE + function (for example, if some interfaces only + support half-duplex), there will be fewer rows + in this table than in the dot3StatsTable." + ::= { dot3 10 } + + dot3PauseEntry OBJECT-TYPE + SYNTAX Dot3PauseEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "An entry in the table, containing information + about the MAC Control PAUSE function on a single + ethernet-like interface." + INDEX { dot3StatsIndex } + ::= { dot3PauseTable 1 } + + Dot3PauseEntry ::= + + SEQUENCE { + dot3PauseAdminMode INTEGER, + dot3PauseOperMode INTEGER, + dot3InPauseFrames Counter32, + dot3OutPauseFrames Counter32, + dot3HCInPauseFrames Counter64, + dot3HCOutPauseFrames Counter64 + } + + dot3PauseAdminMode OBJECT-TYPE + SYNTAX INTEGER { + disabled(1), + enabledXmit(2), + enabledRcv(3), + enabledXmitAndRcv(4) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION "This object is used to configure the default + administrative PAUSE mode for this interface. + + This object represents the + administratively-configured PAUSE mode for this + interface. If auto-negotiation is not enabled + or is not implemented for the active MAU + attached to this interface, the value of this + object determines the operational PAUSE mode + of the interface whenever it is operating in + full-duplex mode. In this case, a set to this + object will force the interface into the + specified mode. + + If auto-negotiation is implemented and enabled + for the MAU attached to this interface, the + PAUSE mode for this interface is determined by + auto-negotiation, and the value of this object + denotes the mode to which the interface will + automatically revert if/when auto-negotiation is + later disabled. Note that when auto-negotiation + is running, administrative control of the PAUSE + mode may be accomplished using the + ifMauAutoNegCapAdvertisedBits object in the + MAU-MIB. + + Note that the value of this object is ignored + when the interface is not operating in + full-duplex mode. + + An attempt to set this object to + 'enabledXmit(2)' or 'enabledRcv(3)' will fail + on interfaces that do not support operation + at greater than 100 Mb/s." + ::= { dot3PauseEntry 1 } + + dot3PauseOperMode OBJECT-TYPE + SYNTAX INTEGER { + disabled(1), + enabledXmit(2), + enabledRcv(3), + enabledXmitAndRcv(4) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION "This object reflects the PAUSE mode currently + + in use on this interface, as determined by + either (1) the result of the auto-negotiation + function or (2) if auto-negotiation is not + enabled or is not implemented for the active MAU + attached to this interface, by the value of + dot3PauseAdminMode. Interfaces operating at + 100 Mb/s or less will never return + 'enabledXmit(2)' or 'enabledRcv(3)'. Interfaces + operating in half-duplex mode will always return + 'disabled(1)'. Interfaces on which + auto-negotiation is enabled but not yet + completed should return the value + 'disabled(1)'." + ::= { dot3PauseEntry 2 } + + dot3InPauseFrames OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of MAC Control frames received on this + interface with an opcode indicating the PAUSE + operation. + + This counter does not increment when the + interface is operating in half-duplex mode. + + For interfaces operating at 10 Gb/s, this + counter can roll over in less than 5 minutes if + it is incrementing at its maximum rate. Since + that amount of time could be less than a + management station's poll cycle time, in order + to avoid a loss of information, a management + station is advised to poll the + dot3HCInPauseFrames object for 10 Gb/s or + faster interfaces. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.4.3, + aPAUSEMACCtrlFramesReceived." + ::= { dot3PauseEntry 3 } + + dot3OutPauseFrames OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of MAC Control frames transmitted on + this interface with an opcode indicating the + PAUSE operation. + + This counter does not increment when the + interface is operating in half-duplex mode. + + For interfaces operating at 10 Gb/s, this + counter can roll over in less than 5 minutes if + it is incrementing at its maximum rate. Since + that amount of time could be less than a + management station's poll cycle time, in order + to avoid a loss of information, a management + station is advised to poll the + dot3HCOutPauseFrames object for 10 Gb/s or + faster interfaces. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.4.2, + aPAUSEMACCtrlFramesTransmitted." + ::= { dot3PauseEntry 4 } + + dot3HCInPauseFrames OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of MAC Control frames received on this + interface with an opcode indicating the PAUSE + operation. + + This counter does not increment when the + interface is operating in half-duplex mode. + + This counter is a 64 bit version of + dot3InPauseFrames. It should be used on + interfaces operating at 10 Gb/s or faster. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.4.3, + aPAUSEMACCtrlFramesReceived." + ::= { dot3PauseEntry 5 } + + dot3HCOutPauseFrames OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of MAC Control frames transmitted on + this interface with an opcode indicating the + PAUSE operation. + + This counter does not increment when the + interface is operating in half-duplex mode. + + This counter is a 64 bit version of + dot3OutPauseFrames. It should be used on + interfaces operating at 10 Gb/s or faster. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.4.2, + aPAUSEMACCtrlFramesTransmitted." + ::= { dot3PauseEntry 6 } + + dot3HCStatsTable OBJECT-TYPE + SYNTAX SEQUENCE OF Dot3HCStatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "A table containing 64-bit versions of error + counters from the dot3StatsTable. The 32-bit + versions of these counters may roll over quite + quickly on higher speed ethernet interfaces. + The counters that have 64-bit versions in this + table are the counters that apply to full-duplex + interfaces, since 10 Gb/s and faster + ethernet-like interfaces do not support + half-duplex, and very few 1000 Mb/s + ethernet-like interfaces support half-duplex. + + Entries in this table are recommended for + interfaces capable of operating at 1000 Mb/s or + faster, and are required for interfaces capable + of operating at 10 Gb/s or faster. Lower speed + ethernet-like interfaces do not need entries in + this table, in which case there may be fewer + entries in this table than in the + dot3StatsTable. However, implementations + containing interfaces with a mix of speeds may + choose to implement entries in this table for + + all ethernet-like interfaces." + ::= { dot3 11 } + + dot3HCStatsEntry OBJECT-TYPE + SYNTAX Dot3HCStatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION "An entry containing 64-bit statistics for a + single ethernet-like interface." + INDEX { dot3StatsIndex } + ::= { dot3HCStatsTable 1 } + + Dot3HCStatsEntry ::= + SEQUENCE { + dot3HCStatsAlignmentErrors Counter64, + dot3HCStatsFCSErrors Counter64, + dot3HCStatsInternalMacTransmitErrors Counter64, + dot3HCStatsFrameTooLongs Counter64, + dot3HCStatsInternalMacReceiveErrors Counter64, + dot3HCStatsSymbolErrors Counter64 + } + + dot3HCStatsAlignmentErrors OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames received on a particular + interface that are not an integral number of + octets in length and do not pass the FCS check. + + The count represented by an instance of this + object is incremented when the alignmentError + status is returned by the MAC service to the + LLC (or other MAC user). Received frames for + which multiple error conditions pertain are, + according to the conventions of IEEE 802.3 + Layer Management, counted exclusively according + to the error status presented to the LLC. + + This counter does not increment for group + encoding schemes greater than 4 bits per group. + + This counter is a 64 bit version of + dot3StatsAlignmentErrors. It should be used + on interfaces operating at 10 Gb/s or faster. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.7, + aAlignmentErrors" + ::= { dot3HCStatsEntry 1 } + + dot3HCStatsFCSErrors OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames received on a particular + interface that are an integral number of octets + in length but do not pass the FCS check. This + count does not include frames received with + frame-too-long or frame-too-short error. + + The count represented by an instance of this + object is incremented when the frameCheckError + status is returned by the MAC service to the + LLC (or other MAC user). Received frames for + which multiple error conditions pertain are, + according to the conventions of IEEE 802.3 + Layer Management, counted exclusively according + to the error status presented to the LLC. + + Note: Coding errors detected by the physical + layer for speeds above 10 Mb/s will cause the + frame to fail the FCS check. + + This counter is a 64 bit version of + dot3StatsFCSErrors. It should be used on + interfaces operating at 10 Gb/s or faster. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.6, + aFrameCheckSequenceErrors." + ::= { dot3HCStatsEntry 2 } + + dot3HCStatsInternalMacTransmitErrors OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames for which transmission on a + particular interface fails due to an internal + MAC sublayer transmit error. A frame is only + + counted by an instance of this object if it is + not counted by the corresponding instance of + either the dot3StatsLateCollisions object, the + dot3StatsExcessiveCollisions object, or the + dot3StatsCarrierSenseErrors object. + + The precise meaning of the count represented by + an instance of this object is implementation- + specific. In particular, an instance of this + object may represent a count of transmission + errors on a particular interface that are not + otherwise counted. + + This counter is a 64 bit version of + dot3StatsInternalMacTransmitErrors. It should + be used on interfaces operating at 10 Gb/s or + faster. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.12, + aFramesLostDueToIntMACXmitError." + ::= { dot3HCStatsEntry 3 } + + dot3HCStatsFrameTooLongs OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames received on a particular + interface that exceed the maximum permitted + frame size. + + The count represented by an instance of this + object is incremented when the frameTooLong + status is returned by the MAC service to the + LLC (or other MAC user). Received frames for + which multiple error conditions pertain are, + according to the conventions of IEEE 802.3 + Layer Management, counted exclusively according + to the error status presented to the LLC. + + This counter is a 64 bit version of + dot3StatsFrameTooLongs. It should be used on + interfaces operating at 10 Gb/s or faster. + + Discontinuities in the value of this counter can + + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.25, + aFrameTooLongErrors." + ::= { dot3HCStatsEntry 4 } + + dot3HCStatsInternalMacReceiveErrors OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "A count of frames for which reception on a + particular interface fails due to an internal + MAC sublayer receive error. A frame is only + counted by an instance of this object if it is + not counted by the corresponding instance of + either the dot3StatsFrameTooLongs object, the + dot3StatsAlignmentErrors object, or the + dot3StatsFCSErrors object. + + The precise meaning of the count represented by + an instance of this object is implementation- + specific. In particular, an instance of this + object may represent a count of receive errors + on a particular interface that are not + otherwise counted. + + This counter is a 64 bit version of + dot3StatsInternalMacReceiveErrors. It should be + used on interfaces operating at 10 Gb/s or + faster. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.1.1.15, + aFramesLostDueToIntMACRcvError." + ::= { dot3HCStatsEntry 5 } + + dot3HCStatsSymbolErrors OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION "For an interface operating at 100 Mb/s, the + number of times there was an invalid data symbol + when a valid carrier was present. + + For an interface operating in half-duplex mode + at 1000 Mb/s, the number of times the receiving + media is non-idle (a carrier event) for a period + of time equal to or greater than slotTime, and + during which there was at least one occurrence + of an event that causes the PHY to indicate + 'Data reception error' or 'carrier extend error' + on the GMII. + + For an interface operating in full-duplex mode + at 1000 Mb/s, the number of times the receiving + media is non-idle (a carrier event) for a period + of time equal to or greater than minFrameSize, + and during which there was at least one + occurrence of an event that causes the PHY to + indicate 'Data reception error' on the GMII. + + For an interface operating at 10 Gb/s, the + number of times the receiving media is non-idle + (a carrier event) for a period of time equal to + or greater than minFrameSize, and during which + there was at least one occurrence of an event + that causes the PHY to indicate 'Receive Error' + on the XGMII. + + The count represented by an instance of this + object is incremented at most once per carrier + event, even if multiple symbol errors occur + during the carrier event. This count does + not increment if a collision is present. + + This counter is a 64 bit version of + dot3StatsSymbolErrors. It should be used on + interfaces operating at 10 Gb/s or faster. + + Discontinuities in the value of this counter can + occur at re-initialization of the management + system, and at other times as indicated by the + value of ifCounterDiscontinuityTime." + REFERENCE "[IEEE 802.3 Std.], 30.3.2.1.5, + aSymbolErrorDuringCarrier." + ::= { dot3HCStatsEntry 6 } + + -- 802.3 Tests + + dot3Tests OBJECT IDENTIFIER ::= { dot3 6 } + + dot3Errors OBJECT IDENTIFIER ::= { dot3 7 } + + -- TDR Test + + dot3TestTdr OBJECT-IDENTITY + STATUS deprecated + DESCRIPTION "******** THIS IDENTITY IS DEPRECATED ******* + + The Time-Domain Reflectometry (TDR) test is + specific to ethernet-like interfaces of type + 10Base5 and 10Base2. The TDR value may be + useful in determining the approximate distance + to a cable fault. It is advisable to repeat + this test to check for a consistent resulting + TDR value, to verify that there is a fault. + + A TDR test returns as its result the time + interval, measured in 10 MHz ticks or 100 nsec + units, between the start of TDR test + transmission and the subsequent detection of a + collision or deassertion of carrier. On + successful completion of a TDR test, the result + is stored as the value of an appropriate + instance of an appropriate vendor specific MIB + object, and the OBJECT IDENTIFIER of that + instance is stored in the appropriate instance + of the appropriate test result code object + (thereby indicating where the result has been + stored). + + This object identity has been deprecated, since + the ifTestTable in the IF-MIB was deprecated, + and there is no longer a standard mechanism for + initiating an interface test. This left no + standard way of using this object identity." + ::= { dot3Tests 1 } + + -- Loopback Test + + dot3TestLoopBack OBJECT-IDENTITY + STATUS deprecated + DESCRIPTION "******** THIS IDENTITY IS DEPRECATED ******* + + This test configures the MAC chip and executes + an internal loopback test of memory, data paths, + and the MAC chip logic. This loopback test can + only be executed if the interface is offline. + Once the test has completed, the MAC chip should + + be reinitialized for network operation, but it + should remain offline. + + If an error occurs during a test, the + appropriate test result object will be set + to indicate a failure. The two OBJECT + IDENTIFIER values dot3ErrorInitError and + dot3ErrorLoopbackError may be used to provided + more information as values for an appropriate + test result code object. + + This object identity has been deprecated, since + the ifTestTable in the IF-MIB was deprecated, + and there is no longer a standard mechanism for + initiating an interface test. This left no + standard way of using this object identity." + ::= { dot3Tests 2 } + + dot3ErrorInitError OBJECT-IDENTITY + STATUS deprecated + DESCRIPTION "******** THIS IDENTITY IS DEPRECATED ******* + + Couldn't initialize MAC chip for test. + + This object identity has been deprecated, since + the ifTestTable in the IF-MIB was deprecated, + and there is no longer a standard mechanism for + initiating an interface test. This left no + standard way of using this object identity." + ::= { dot3Errors 1 } + + dot3ErrorLoopbackError OBJECT-IDENTITY + STATUS deprecated + DESCRIPTION "******** THIS IDENTITY IS DEPRECATED ******* + + Expected data not received (or not received + correctly) in loopback test. + + This object identity has been deprecated, since + the ifTestTable in the IF-MIB was deprecated, + and there is no longer a standard mechanism for + initiating an interface test. This left no + standard way of using this object identity." + ::= { dot3Errors 2 } + + -- { dot3 8 }, the dot3ChipSets tree, is defined in [RFC2666] + + -- conformance information + + etherConformance OBJECT IDENTIFIER ::= { etherMIB 2 } + + etherGroups OBJECT IDENTIFIER ::= { etherConformance 1 } + etherCompliances OBJECT IDENTIFIER ::= { etherConformance 2 } + + -- compliance statements + + etherCompliance MODULE-COMPLIANCE + STATUS deprecated + DESCRIPTION "******** THIS COMPLIANCE IS DEPRECATED ******** + + The compliance statement for managed network + entities which have ethernet-like network + interfaces. + + This compliance is deprecated and replaced by + dot3Compliance." + + MODULE -- this module + MANDATORY-GROUPS { etherStatsGroup } + + GROUP etherCollisionTableGroup + DESCRIPTION "This group is optional. It is appropriate + for all systems which have the necessary + metering. Implementation in such systems is + highly recommended." + ::= { etherCompliances 1 } + + ether100MbsCompliance MODULE-COMPLIANCE + STATUS deprecated + DESCRIPTION "******** THIS COMPLIANCE IS DEPRECATED ******** + + The compliance statement for managed network + entities which have 100 Mb/sec ethernet-like + network interfaces. + + This compliance is deprecated and replaced by + dot3Compliance." + + MODULE -- this module + MANDATORY-GROUPS { etherStats100MbsGroup } + + GROUP etherCollisionTableGroup + DESCRIPTION "This group is optional. It is appropriate + for all systems which have the necessary + metering. Implementation in such systems is + highly recommended." + ::= { etherCompliances 2 } + + dot3Compliance MODULE-COMPLIANCE + STATUS deprecated + DESCRIPTION "******** THIS COMPLIANCE IS DEPRECATED ******** + + The compliance statement for managed network + entities which have ethernet-like network + interfaces. + + This compliance is deprecated and replaced by + dot3Compliance2." + + MODULE -- this module + MANDATORY-GROUPS { etherStatsBaseGroup } + + GROUP etherDuplexGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces which are + capable of operating in full-duplex mode. + It is highly recommended for all + ethernet-like network interfaces." + + GROUP etherStatsLowSpeedGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces which are + capable of operating at 10 Mb/s or slower in + half-duplex mode." + + GROUP etherStatsHighSpeedGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces which are + capable of operating at 100 Mb/s or faster." + + GROUP etherControlGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces that + support the MAC Control sublayer." + + GROUP etherControlPauseGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces that + support the MAC Control PAUSE function." + + GROUP etherCollisionTableGroup + DESCRIPTION "This group is optional. It is appropriate + for all ethernet-like network interfaces + which are capable of operating in + half-duplex mode and have the necessary + metering. Implementation in systems with + + such interfaces is highly recommended." + ::= { etherCompliances 3 } + + dot3Compliance2 MODULE-COMPLIANCE + STATUS current + DESCRIPTION "The compliance statement for managed network + entities which have ethernet-like network + interfaces. + + Note that compliance with this MIB module + requires compliance with the ifCompliance3 + MODULE-COMPLIANCE statement of the IF-MIB + (RFC2863). In addition, compliance with this + MIB module requires compliance with the + mauModIfCompl3 MODULE-COMPLIANCE statement of + the MAU-MIB (RFC3636)." + + MODULE -- this module + MANDATORY-GROUPS { etherStatsBaseGroup2 } + + GROUP etherDuplexGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces which are + capable of operating in full-duplex mode. + It is highly recommended for all + ethernet-like network interfaces." + + GROUP etherRateControlGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces which are + capable of operating at speeds faster than + 1000 Mb/s. It is highly recommended for all + ethernet-like network interfaces." + + GROUP etherStatsLowSpeedGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces which are + capable of operating at 10 Mb/s or slower in + half-duplex mode." + + GROUP etherStatsHighSpeedGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces which are + capable of operating at 100 Mb/s or faster." + + GROUP etherStatsHalfDuplexGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces which are + + capable of operating in half-duplex mode." + + GROUP etherHCStatsGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces which are + capable of operating at 10 Gb/s or faster. + It is recommended for all ethernet-like + network interfaces which are capable of + operating at 1000 Mb/s or faster." + + GROUP etherControlGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces that + support the MAC Control sublayer." + + GROUP etherHCControlGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces that + support the MAC Control sublayer and are + capable of operating at 10 Gb/s or faster." + + GROUP etherControlPauseGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces that + support the MAC Control PAUSE function." + + GROUP etherHCControlPauseGroup + DESCRIPTION "This group is mandatory for all + ethernet-like network interfaces that + support the MAC Control PAUSE function and + are capable of operating at 10 Gb/s or + faster." + + GROUP etherCollisionTableGroup + DESCRIPTION "This group is optional. It is appropriate + for all ethernet-like network interfaces + which are capable of operating in + half-duplex mode and have the necessary + metering. Implementation in systems with + such interfaces is highly recommended." + ::= { etherCompliances 4 } + + -- units of conformance + + etherStatsGroup OBJECT-GROUP + OBJECTS { dot3StatsIndex, + dot3StatsAlignmentErrors, + dot3StatsFCSErrors, + dot3StatsSingleCollisionFrames, + dot3StatsMultipleCollisionFrames, + dot3StatsSQETestErrors, + dot3StatsDeferredTransmissions, + dot3StatsLateCollisions, + dot3StatsExcessiveCollisions, + dot3StatsInternalMacTransmitErrors, + dot3StatsCarrierSenseErrors, + dot3StatsFrameTooLongs, + dot3StatsInternalMacReceiveErrors, + dot3StatsEtherChipSet + } + STATUS deprecated + DESCRIPTION "********* THIS GROUP IS DEPRECATED ********** + + A collection of objects providing information + applicable to all ethernet-like network + interfaces. + + This object group has been deprecated and + replaced by etherStatsBaseGroup and + etherStatsLowSpeedGroup." + ::= { etherGroups 1 } + + etherCollisionTableGroup OBJECT-GROUP + OBJECTS { dot3CollFrequencies + } + STATUS current + DESCRIPTION "A collection of objects providing a histogram + of packets successfully transmitted after + experiencing exactly N collisions." + ::= { etherGroups 2 } + + etherStats100MbsGroup OBJECT-GROUP + OBJECTS { dot3StatsIndex, + dot3StatsAlignmentErrors, + dot3StatsFCSErrors, + dot3StatsSingleCollisionFrames, + dot3StatsMultipleCollisionFrames, + dot3StatsDeferredTransmissions, + dot3StatsLateCollisions, + dot3StatsExcessiveCollisions, + dot3StatsInternalMacTransmitErrors, + dot3StatsCarrierSenseErrors, + dot3StatsFrameTooLongs, + dot3StatsInternalMacReceiveErrors, + dot3StatsEtherChipSet, + dot3StatsSymbolErrors + + } + STATUS deprecated + DESCRIPTION "********* THIS GROUP IS DEPRECATED ********** + + A collection of objects providing information + applicable to 100 Mb/sec ethernet-like network + interfaces. + + This object group has been deprecated and + replaced by etherStatsBaseGroup and + etherStatsHighSpeedGroup." + ::= { etherGroups 3 } + + etherStatsBaseGroup OBJECT-GROUP + OBJECTS { dot3StatsIndex, + dot3StatsAlignmentErrors, + dot3StatsFCSErrors, + dot3StatsSingleCollisionFrames, + dot3StatsMultipleCollisionFrames, + dot3StatsDeferredTransmissions, + dot3StatsLateCollisions, + dot3StatsExcessiveCollisions, + dot3StatsInternalMacTransmitErrors, + dot3StatsCarrierSenseErrors, + dot3StatsFrameTooLongs, + dot3StatsInternalMacReceiveErrors + } + STATUS deprecated + DESCRIPTION "********* THIS GROUP IS DEPRECATED ********** + + A collection of objects providing information + applicable to all ethernet-like network + interfaces. + + This object group has been deprecated and + replaced by etherStatsBaseGroup2 and + etherStatsHalfDuplexGroup, to separate + objects which must be implemented by all + ethernet-like network interfaces from + objects that need only be implemented on + ethernet-like network interfaces that are + capable of half-duplex operation." + ::= { etherGroups 4 } + + etherStatsLowSpeedGroup OBJECT-GROUP + OBJECTS { dot3StatsSQETestErrors } + STATUS current + DESCRIPTION "A collection of objects providing information + + applicable to ethernet-like network interfaces + capable of operating at 10 Mb/s or slower in + half-duplex mode." + ::= { etherGroups 5 } + + etherStatsHighSpeedGroup OBJECT-GROUP + OBJECTS { dot3StatsSymbolErrors } + STATUS current + DESCRIPTION "A collection of objects providing information + applicable to ethernet-like network interfaces + capable of operating at 100 Mb/s or faster." + ::= { etherGroups 6 } + + etherDuplexGroup OBJECT-GROUP + OBJECTS { dot3StatsDuplexStatus } + STATUS current + DESCRIPTION "A collection of objects providing information + about the duplex mode of an ethernet-like + network interface." + ::= { etherGroups 7 } + + etherControlGroup OBJECT-GROUP + OBJECTS { dot3ControlFunctionsSupported, + dot3ControlInUnknownOpcodes + } + STATUS current + DESCRIPTION "A collection of objects providing information + about the MAC Control sublayer on ethernet-like + network interfaces." + ::= { etherGroups 8 } + + etherControlPauseGroup OBJECT-GROUP + OBJECTS { dot3PauseAdminMode, + dot3PauseOperMode, + dot3InPauseFrames, + dot3OutPauseFrames + } + STATUS current + DESCRIPTION "A collection of objects providing information + about and control of the MAC Control PAUSE + function on ethernet-like network interfaces." + ::= { etherGroups 9 } + + etherStatsBaseGroup2 OBJECT-GROUP + OBJECTS { dot3StatsIndex, + dot3StatsAlignmentErrors, + dot3StatsFCSErrors, + dot3StatsInternalMacTransmitErrors, + dot3StatsFrameTooLongs, + dot3StatsInternalMacReceiveErrors + } + STATUS current + DESCRIPTION "A collection of objects providing information + applicable to all ethernet-like network + interfaces." + ::= { etherGroups 10 } + + etherStatsHalfDuplexGroup OBJECT-GROUP + OBJECTS { dot3StatsSingleCollisionFrames, + dot3StatsMultipleCollisionFrames, + dot3StatsDeferredTransmissions, + dot3StatsLateCollisions, + dot3StatsExcessiveCollisions, + dot3StatsCarrierSenseErrors + } + STATUS current + DESCRIPTION "A collection of objects providing information + applicable only to half-duplex ethernet-like + network interfaces." + ::= { etherGroups 11 } + + etherHCStatsGroup OBJECT-GROUP + OBJECTS { dot3HCStatsAlignmentErrors, + dot3HCStatsFCSErrors, + dot3HCStatsInternalMacTransmitErrors, + dot3HCStatsFrameTooLongs, + dot3HCStatsInternalMacReceiveErrors, + dot3HCStatsSymbolErrors + } + STATUS current + DESCRIPTION "A collection of objects providing high-capacity + statistics applicable to higher-speed + ethernet-like network interfaces." + ::= { etherGroups 12 } + + etherHCControlGroup OBJECT-GROUP + OBJECTS { dot3HCControlInUnknownOpcodes } + STATUS current + DESCRIPTION "A collection of objects providing high-capacity + statistics for the MAC Control sublayer on + higher-speed ethernet-like network interfaces." + ::= { etherGroups 13 } + + etherHCControlPauseGroup OBJECT-GROUP + OBJECTS { dot3HCInPauseFrames, + dot3HCOutPauseFrames + + } + STATUS current + DESCRIPTION "A collection of objects providing high-capacity + statistics for the MAC Control PAUSE function on + higher-speed ethernet-like network interfaces." + ::= { etherGroups 14 } + + etherRateControlGroup OBJECT-GROUP + OBJECTS { dot3StatsRateControlAbility, + dot3StatsRateControlStatus + } + STATUS current + DESCRIPTION "A collection of objects providing information + about the Rate Control function on ethernet-like + interfaces." + ::= { etherGroups 15 } + +END -- cgit v1.2.3